Using Lost wax method to create Jewelry

...It can be hard wax, soft wax, sticky, shrinking or non-shrinking

Moon Phase

Day 1

Waxing
Full Moon in: 13 Days

Latest news

May 20:  Beautiful!!! We received the rings last week and we just love them. read more

May 12:  "... I must say that this ring is extremely poweful. ..read more..."


Subscribe to Atlantis Ring News Letter
Get the latest
"Magic" news
Email:
 



Site Navigation:

Old layout

Skip Navigation Links.

 Gold 18K Wedding Ring


We accept Paypal

 

Login

Skype Me™!

IM me 


Links:



Afflilate code:  

f76d527b-e2a8-424c-8972-e7325f305a6e

Skip Navigation LinksHome > WorkShop > Lost Wax method

 

The making of a piece of jewelry with the lost wax method.

It is called so because the wax model is burned away when the mold is created.

The making of a metal Atlantis Ring today is just like small metal objects were made in ancient times. Of course today the materials are better, but the principle is still the same.

History of jewelry making compared with modern techniques.

In the past beeswax was used to make the desired object. Today we have many different kinds of wax. It can be hard wax, soft wax, sticky, shrinking or non-shrinking. In the past clay was taken from the shore of a river. The wax object was embedded in the clay with a hole left open. Today the wax object is embedded in a special heat resisting kind of plaster called investment powder. The powder is mixed with water and poured in a cylinder that holds the wax model. In order to get air-bubbles out of the mixture it is put under vacuum. The cylinder with the still liquid plaster is placed under a bell jar and the air is removed by means of a vacuum pump. The air is let back in and the investment now has no more air bubbles that would become small metal balls on the object once the molten metal goes in. In the past the dried clay with the wax inside was put on a charcoal fire. Air was blown onto the fire and the clay baked until hard. At the same time the wax burned away and the mold was created. melting of the gold, before it is used of casting jewelry Today the hardened investment with the wax model inside goes into an oven. The wax is burned out and the mold is ready to receive molten metal. In the old days the metal was melted by blowing lots of air towards the fire that held a clay crucible with the metal in it and once liquid, it was poured in the clay mold. The clay was then broken and the object released. Today we heat the metal with a torch that burns gas and oxygen, and the pouring of the metal into the mold has been very much sophisticated. Because liquid metal has a viscosity that resembles treacle, it is so thick that it will not flow easily into every recess of more or less intricate designs. Therefore different methods have been developed to force the molten metal down into the mold. The channel towards the object inside the mold is called a sprue and has to be wide enough to let the metal flow through fast enough. Not too wide so that it becomes difficult to cut it from the object later. Many thin sprues are better than one thick one.   One way to force the metal down was as follows. Imagine a cylindrical mold, with a wide opening on the top tapering towards the object inside. The metal was put in the wide opening and heated until liquid. Then a half cut potato or a wet cloth was pressed on top of the molten metal. The steam that developed forced the molten metal into the mold.

You know how water stays in a bucket when you swing it around, and that principle was used in the next method. The cylinder with the molten metal in the opening was attached to a 2-meter chain. When the metal was hot enough it was swung around in a circle as fast as possible so that the centrifugal force pushed the metal in the mold. You can imagine how risky those two methods were. Based upon the idea of centrifugal force a dentist some 70 years ago invented a spring driven casting machine. The cylinder is placed on a horizontal arm that is attached to a wound-up spring. The crucible with a hole in the side is placed with the opening against the cylinder. The metal in the crucible is heated to liquidus and the spring released. The arm turns very fast and the liquid metal is thrown in the cylinder with considerable force. The newest method is based upon the fact that the solid investment is porous and air can pass through. The cylindrical mold coming out of the oven is placed on a suction hole that creates a vacuum under it. Air flows from the opening in the top through the mold and when the liquid metal is poured into the top hole, it flows in every small recess of the mold. Once the metal is in the mold, it is allowed to cool a little and then the mold is quenched in water. The investment powder broken away and the object, ring or whatever is cleaned. The sprue is cut of and the piece filed, sanded and polished.